resolving dynamic hard disk /windows 7 installation issues
Support Home
Solution Centers
Advanced Search
Buy Products
Article ID: 927520 - Last Review: September 14, 2007 - Revision: 2.6
You cannot select or format a hard disk partition when you try to install Windows Vista, Windows 7 or Windows Server 2008 R2
View products that this article applies to.
Support for Windows Vista without any service packs installed ended on April 13, 2010. To continue receiving security updates for Windows, make sure you're running Windows Vista with Service Pack 2 (SP2). For more information, refer to this Microsoft web page: Support is ending for some versions of Windows
Important Dynamic discs are only supported for:
Windows Vista Business
Windows Vista Enterprise
Windows Vista Ultimate.
Windows 7 Enterprise
Windows 7 Professional
Windows 7 Ultimate
Windows Server 2008 R2 Datacenter
Windows Server 2008 R2 Enterprise
Windows Server 2008 R2 Standard
Windows Web Server 2008 R2
They are not supported for Windows Vista Home Basic, Windows Vista Home Premium, Windows 7 Home Basic, Windows 7 Starter, and Windows 7 Home Premium.
There is one exception. When you upgrade your computer from Windows XP Media Center Edition to Windows Vista Home Premium, some dynamic discs are handled and supported.
Expand all | Collapse all
SYMPTOMS
When you try to install Windows Vista, Windows 7 or Windows Server 2008 R2, you may experience one or more of the following symptoms:
The hard disk on which you want to install Windows Vista, Windows 7 or Windows Server 2008 R2is not listed.
You cannot select a hard disk partition on which to install Windows Vista, Windows 7 or Windows Server 2008 R2..
You cannot format a hard disk partition or partitions.
You cannot set the correct size for a hard disk partition.
You receive the following error message:
Windows is unable to find a system volume that meets its criteria for installation
Back to the top
CAUSE
This problem may occur for one of the following reasons:
Windows is incompatible with a mass storage controller or a mass storage driver.
A mass storage controller or a mass storage driver is outdated.
The hard disk on which you want to install Windows Vista, Windows 7 or Windows Server 2008 R2 is a dynamic disk.
A data cable in the computer is loose, or another hardware issue has occurred.
The hard disk or the Windows file system is damaged.
You tried to select a FAT32 partition or another type of partition that is incompatible with Windows Vista, Windows 7 or Windows Server 2008 R2.
Back to the top
RESOLUTION
To resolve this problem, use one or more of the following methods.
Method 1: Verify that the partition is compatible with Windows
You cannot install Windows on a FAT32 partition. Additionally, you must correctly configure dynamic disks for use with Windows. To verify that the partition is compatible with Windows Vista, Windows 7 or Windows Server 2008 R2, follow these steps:
For a dynamic disk that has a simple volume, use the Diskpart.exe utility to configure the disk as an active disk. For more information about how to use the Diskpart.exe utility, click the following article number to view the article in the Microsoft Knowledge Base:
300415 A description of the Diskpart.exe command-line utility
For a FAT32 partition, reformat the partition, or convert the partition to an NTFS file system partition by using the Convert.exe command.
Note When you format a partition, all data is removed from the partition. This data includes all the files on the partition. For more information about how to use the Convert.exe command, click the following article number to view the article in the Microsoft Knowledge Base:
314097 How to use Convert.exe to convert a partition to the NTFS file system
Method 2: Update the drivers for the hard disk controller
If you want to install Windows Vista Windows 7 or Windows Server 2008 R2 as an upgrade, update the drivers for the hard disk controller to the latest drivers.
Note Windows Setup provides a feature to migrate current drivers to the new operating system. Therefore, Windows Setup may use the drivers that are currently installed on the computer. If the computer does not have the latest drivers installed, the Setup program may use the outdated drivers. In this case, you may experience compatibility problems.
Method 3: Provide the correct drivers for the hard disk controller
If you are trying to perform a clean installation of Windows, you must provide the correct drivers for the hard disk controller. When you are prompted to select the disk on which to install Windows, you must also click to select the Load Driver option. Windows Setup will guide you through the rest of the process.
Method 4: Examine the Setupact.log file to verify that the partition is active
If you receive the following error message, verify that the partition is active by examining the Setupact.log file:
Windows is unable to find a system volume that meets its criteria for installation
Notes
If you install Windows Vista, Windows 7 or Windows Server 2008 R2 as an upgrade, the Setupact.log file is located in the Drive:\$WINDOWS.~BT\Sources\Panther folder. Drive represents the drive that contains the existing Windows installation.
If you perform a clean installation of Windows Vista, Windows 7 or Windows Server 2008 R2, the Setupact.log file is located in the Drive:\$WINDOWS\Sources\Panther folder. Drive represents the DVD drive that contains the Windows Setup files.
To verify that the partition is active, follow these steps:
Insert the DVD into the DVD drive.
On the disk selection screen, press SHIFT+F10. A Command Prompt (CMD) window opens.
Change the directory to locate the Setupact.log file, and then open the Setupact.log file.
Locate the "DumpDiskInformation" section. This section contains information about partition mapping.
In the "DumpDiskInformation" section, locate the log entry that resembles the following.
Disk [0] partition [1] is an active partition
If this log entry appears after an entry that resembles the following, the hard disk may not be configured to use a Windows-based operating system.
Unknown
In this case, use the Diskpart.exe utility to configure a different partition as active.
Note This step prevents a third-party operating system from starting.
Close the Command Prompt window.
Method 5: Check for firmware updates and for system BIOS updates
For firmware updates and for system BIOS updates, contact the manufacturer of the hardware in the computer, visit the following Web site:
http://support.microsoft.com/gp/vendors/en-us
Method 6: Verify that the system BIOS correctly detects the hard disk
For information about how to verify that the system BIOS correctly detects the hard disk, contact the manufacturer of the computer hardware.
Method 7: Use the Chkdsk.exe utility to check for problems
Run the Chkdsk.exe utility to check for disk problems. Replace the hard disk if it is damaged.
Method 8: Use the Diskpart.exe utility to clean the disk, and then run Windows Setup again
If you have tried all the methods that are listed in this section and the problem persists, use the Diskpart.exe utility to clean the disk, and then run Windows Setup again.
Note Use this method only if you want to perform a clean installation of Windows. When you clean the hard disk, it is formatted. All partitions and all data on the hard disk are permanently removed. We strongly recommend that you back up the files on the hard disk before you clean the disk.
To use the Diskpart.exe utility to clean the hard disk, follow these steps:
Insert the DVD into the DVD drive.
On the disk selection screen, press SHIFT+F10. A Command Prompt window opens.
Type diskpart, and then press ENTER to open the diskpart tool.
Type list disk, and then press ENTER. A list of available hard disks is displayed.
Type sel disk number, and then press ENTER. number is the number of the hard disk that you want to clean. The hard disk is now selected.
Type det disk, and then press ENTER. A list of partitions on the hard disk is displayed. Use this information to verify that the correct disk is selected.
Make sure that the disk does not contain required data, type clean all, and then press ENTER to clean the disk. All the partitions and all the data on the disk is permanently removed.
Type exit, and then press ENTER to close the diskpart tool.
Close the Command Prompt window.
Click the Refresh button to update the disk selection screen. This step lists the disk.
Run Windows Setup to perform a clean installation of Windows.
Back to the top
Subscribe to:
Post Comments (Atom)